Optimization of Operating Modes of Pumping Stations Equipped With Parallel-Operated Centrifugal Pumps

Article Sidebar

PDF
Published: 2026-01-24
DOI: https://doi.org/10.51699/cd5vpj68

Main Article Content

Urishev Boboraum
Doctor of Technical Sciences, Professor of the Department of Karshi State Technical University.
Juraev Sanjar Rashidovich
PhD, Head of the Department of Tashkent State Technical University named after I. A. Karimov
Hayitboev Doston Umidjon o’g’li
Master's student at Tashkent State Technical University named after I.A. Karimov.

Abstract

The article examines the issues of reducing head losses and optimizing electricity consumption in pumping stations operating in parallel pump mode. A method is proposed to increase energy efficiency by reducing the hydraulic resistances of the pipeline system for parallel-operated pumps and selecting the pipe diameter at an economically optimal value. Using the example of three D1600–90 pumps, capital and operational costs were analyzed for various pipe diameters, and optimal options were identified. The calculations show that correct selection of the pipe diameter ensures that the pumps operate within their optimal working range and allows a significant reduction in electricity consumption over the season.

Article Details

Issue

Vol. 4 No. 1 (2026): Innovative: International Multi-disciplinary Journal of Applied Technology

Section

Articles

How to Cite

Optimization of Operating Modes of Pumping Stations Equipped With Parallel-Operated Centrifugal Pumps. (2026). Innovative: International Multidisciplinary Journal of Applied Technology (2995-486X), 4(1), 27-32. https://doi.org/10.51699/cd5vpj68

References

[1] B. U. Urishev, Operation of Pumping Stations and Improvement of Energy Efficiency. Qarshi: Intellect, 2021.

[2] V. F. Chebaevsky, K. P. Vishnevsky, and N. N. Nakladov, Design of Pumping Stations and Testing of Pump Installations. Moscow: Kolos, 2000.

[3] J. Bing, Y. Li, and X. Chen, “Energy Saving Analysis of Large Scale Irrigation Pumping Stations,” Irrig. Drain., vol. 68, no. 2, pp. 245–256, 2019.

[4] R. W. Fox, A. T. McDonald, P. J. Pritchard, and J. W. Mitchell, Introduction to Fluid Mechanics, 8th ed. Hoboken: Wiley, 2015.

[5] B. S. Leznov, Energy Saving in Pumping Installations. Moscow: Energoatomizdat, 1991.

[6] A. J. Stepanoff, Centrifugal and Axial Flow Pumps. New York: Wiley, 1957.

[7] R. Singh and F. Nestmann, “Optimized Operation of Pumping Systems for Energy Efficiency,” J. Hydraul. Eng., vol. 144, no. 3, pp. 1–12, 2018.

[8] R. Saidur, “A Review on Electrical Motors Energy Use and Energy Savings,” Renew. Sustain. Energy Rev., vol. 14, no. 3, pp. 877–898, 2010.

[9] M. A. Abdel Meguid and M. A. El Sharkawy, “Energy Optimization of Parallel Pumping Systems,” Energy Rep., vol. 6, pp. 1134–1144, 2020.

[10] H. Zhang and X. Xia, “Optimal Control of Parallel Pumping Systems for Energy Cost Reduction,” Appl. Energy, vol. 190, pp. 140–149, 2017.

[11] M. M. Mukhamadiev, B. U. Urishev, and S. R. Juraev, Improving the Efficiency of Sediment Removal in the Forebay of Irrigation Pumping Stations. Tashkent: Innovatsion rivojlanish, 2025.

[12] I. J. Karassik, J. P. Messina, P. Cooper, and C. C. Heald, Pump Handbook, 3rd ed. New York: McGraw Hill, 2001.

[13] J. F. Gülich, Centrifugal Pumps, 2nd ed. Berlin: Springer, 2010.

[14] R. W. Fox, A. T. McDonald, P. J. Pritchard, and J. W. Mitchell, Introduction to Fluid Mechanics, 8th ed. Hoboken: Wiley, 2015.

[15] P. Morales and J. Gutiérrez, “Life Cycle Cost Analysis Applied to Pumping Systems,” Energy, vol. 69, pp. 287–297, 2014.